To maintain a newly built house, check for leaks, keep drains clear, service equipment and inspect cracks, joints and finishes as materials dry and settle. Start at handover, follow the manufacturers’ maintenance instructions and report defects promptly. Don't assume your home needs no attention just because it's new.
What should you check at handover?
Before you move in, walk through the house with the builder and make a snag list: a written record of incomplete or defective work. Test accessible taps, toilets, lights, switches, doors and windows, and photograph damage before furniture hides it.
Collect the approved drawings, any available as-built drawings showing what was actually installed, equipment manuals, test certificates and warranty documents. Check that the documents match the equipment in your house, particularly pumps, water heaters and cooling systems.
Ask the builder to show you the main water shut-off valve, electrical distribution board, inspection chambers and any water-tank access points. Label isolation valves and circuits clearly so you can turn off the correct supply without trial and error.
Confirm the defect-reporting procedure in writing, including who to contact and any notification deadlines. Check your contract and applicable requirements to establish warranty coverage and who is responsible for repairs. Don't assume your warranty covers every defect or maintenance task.
How often should you maintain a new house?
Use the following schedule as a starting point, then adjust it to suit your house’s design, equipment manuals and what you find during inspections. Check more often if you notice a recurring fault or the builder specifies additional early maintenance.
- During the first few weeks, look under sinks, around toilets and beside pumps for leaks, and check that floor drains empty properly.
- Each month, inspect accessible sealant joints, look for damp patches and check filters according to the equipment instructions.
- Every three to six months, inspect accessible roof drainage, check that windows and doors open and close properly, and examine visible plumbing connections.
- Once a year, arrange any required equipment servicing and check the condition of waterproofing details, exterior joints and protective coatings.
- Before a contractual defect-reporting deadline, inspect the entire house and submit an updated written defect list.
Keep dated photographs, service invoices and a simple maintenance log. These records help you distinguish a new problem from an existing one and track previous repair attempts.
Which cracks need professional inspection?
You may notice fine cracks in plaster, render and joints as new materials lose moisture or move at different rates. A hairline crack in a finish doesn't necessarily mean you have a structural defect, but you should record its location and watch for changes.
Photograph the crack beside a ruler, then take follow-up photographs from the same position. Avoid filling it if the builder or an engineer needs to inspect it first.
Ask a qualified structural engineer to assess growing or displaced cracks, diagonal cracks around openings, cracks extending through masonry, or cracking accompanied by sagging floors or doors that suddenly jam. You can't reliably judge the cause or severity from crack width alone.
For minor defects in finishes, ask the builder when to arrange repairs. Repeated cosmetic patching won't solve continuing movement, loose plaster or moisture entering behind the finish.
How do you maintain waterproofing and drainage?
Inspect accessible roof outlets, gutters where fitted, balcony drains and external drainage channels. Remove debris without pushing it into the pipework, and keep covers and strainers in place. Never enter an inspection chamber or climb onto an unprotected roof to carry out a check.
On flat roofs, look for standing water that doesn't drain, damaged membrane edges and gaps around pipes that pass through the roof. Don't drill into waterproofing or let new equipment supports puncture it without a properly designed seal.
Check sealant around shower trays, baths, sinks and window frames for splits or separation from adjoining surfaces. You can't use surface sealant as a substitute for the waterproofing beneath tiles. If leakage recurs, have the cause investigated rather than applying another bead of sealant.
Fix the moisture source before repainting a damp patch. The US Environmental Protection Agency advises fixing water problems and drying wet materials within 24 to 48 hours to help prevent mould growth.
How do you maintain plumbing and electrical systems?
Check visible pipe joints, pump connections and water-heater connections for drips, corrosion or staining. Report a pump that repeatedly starts and stops, unexplained pressure loss or a water meter that keeps moving when you've stopped all water use. These signs can indicate a fault, though they don't tell you where it is.
Follow the manufacturer's service intervals for pumps, water heaters and any storage tanks. Ask a qualified technician how often you need to have tanks inspected and cleaned, and never enter a water tank yourself.
Include these electrical and ventilation checks in your maintenance schedule:
- Test residual-current protection using the device’s test button at the interval stated on its label or in its instructions.
- Ask a qualified electrician to investigate repeated tripping, discoloured sockets, burning smells or buzzing fittings. Don't remove covers yourself.
- Test smoke alarms using their test buttons and replace batteries or complete units according to their instructions.
- Clean extractor grilles and inspect accessible cooling-system filters and condensate drains as the manufacturer directs.
By maintaining filters, you help preserve airflow and equipment performance. The US Department of Energy recommends cleaning or replacing air-conditioning filters regularly, and more often if dust or heavy use causes them to clog faster.
How should you care for new finishes?
Follow the installer’s instructions before washing fresh paint, applying cleaners or placing heavy furniture on newly finished floors. Paint, grout, adhesives and floor coatings have different curing requirements, so don't assume the same waiting period applies to every surface.
Use cleaning products approved for each material. Acidic cleaners can damage cement-based grout and some natural stone, while excessive water can damage timber flooring and cabinet edges.
Report loose tiles, lifting flooring, swollen joinery and recurring stains before attempting cosmetic repairs. If you suspect a construction defect, document it before repairing it and give the builder an opportunity to inspect, unless you need to act immediately to prevent injury or further damage. Keep receipts and photographs for any urgent work.