Home

Are Small Cracks Normal in a New Building?

Yes, small cracks in a new building are often normal when plaster, render or other finishes dry and shrink. However, you can't judge a crack by its size alone. Check its location, pattern, depth and whether it's changing to help determine whether you need a repair from your builder or an assessment by a structural engineer.

Why do new buildings develop cracks?

Concrete, mortar, plaster and screeds contain water during construction. As excess moisture leaves, these materials can shrink, while adjoining materials restrict their movement. This restraint can produce fine cracks, particularly across large surfaces and where different materials meet.

Drying shrinkage is a recognised cause of concrete cracking, as technical resources from the American Concrete Institute explain. A shrinkage crack isn't automatically a structural defect, but you should still have cracks in structural concrete assessed based on their location and the element's function.

Different materials also expand and contract by different amounts as temperatures change. You may notice cracks where a masonry partition meets a concrete column, where a ceiling meets a wall, or along plasterboard joints if the construction details don't allow enough movement.

Foundation movement is another possibility, but you shouldn't accept that explanation without evidence. Uneven support, poorly compacted fill, leaking underground pipes or construction defects can cause differential settlement, meaning that one part of the building moves more than another.

Which small cracks are usually cosmetic?

A crack is more likely to be cosmetic if it stays within the finish, has no displacement on either side and stops developing. Typical examples include fine crazing in plaster, a narrow line along a plasterboard joint, or a small gap between decorative trim and the wall.

Check the material beneath the finish wherever it's already exposed, but don't chip into a beam, column or slab to investigate. A line in paint may follow a superficial plaster crack, yet a similar-looking line can also conceal movement in the masonry behind it.

Crack width alone isn't a reliable safety test. A hairline crack in a reinforced concrete beam may deserve more attention than a wider gap in a non-structural finish, particularly if the beam also shows deformation or damage.

When recording cracks, you can describe a barely visible line as hairline and measure wider cracks in millimetres. Don't treat any single measurement, including 1 mm or 3 mm, as a universal boundary between safe and unsafe construction.

Which cracks need prompt inspection?

Ask a qualified structural engineer to inspect cracks that affect load-bearing elements, continue to grow or appear alongside other signs of movement. If you know, tell the engineer whether your building uses a reinforced concrete frame, load-bearing masonry or another structural system. Look for these warning signs:

  • Cracks in beams or columns, especially diagonal cracks, cracks near supports or damage that exposes reinforcement.
  • Stepped cracks along masonry joints, or diagonal cracks extending from door and window corners that grow or recur.
  • Cracks in matching positions on both sides of a wall, which may extend beyond the surface finish.
  • Uneven edges or bulging, including one side of a crack projecting beyond the other.
  • Doors that have started sticking, distorted frames, sloping floors or visible separation between connected building elements.
  • Sudden crack growth, falling material, unusual cracking sounds or noticeable sagging.

You can't diagnose the cause from these signs alone. For example, a door may stick because it fits poorly, but several symptoms appearing together give you more reason to suspect movement.

If you notice sudden movement, falling masonry or significant sagging, keep people away from the affected area and seek urgent assistance from a structural engineer or the relevant emergency authority. Don't stay beneath a damaged element while waiting to see whether the crack grows.

How should you monitor a new crack?

Monitoring helps you distinguish a stable defect from continuing movement, but it doesn't replace an inspection if you spot warning signs. Start a record before anyone fills, paints over or otherwise conceals the crack.

  1. Give each crack a reference number and mark its location on a simple room sketch.
  2. Photograph the whole wall or element, then take a close-up with a millimetre scale beside the crack.
  3. Record its length, direction and width at clearly identified points, noting the date and any nearby defects.
  4. Repeat photographs from the same position and compare measurements at the same points.
  5. Send your record to the builder and agree on an inspection and follow-up plan.

A crack-width card can help you compare visible widths. An engineer may specify a fixed crack monitor to measure movement more consistently. Don't rely on a pencil mark or a piece of tape as proof that the structure is stable.

Ask the professional inspecting your building how often you should check the crack. If it changes quickly or you notice other warning signs, report this immediately rather than waiting for the next scheduled check.

When should you repair cracks?

Repair a confirmed cosmetic crack once the underlying movement has settled enough for the specified repair. If you fill it too early, you may hide useful evidence and find that it cracks again.

For a stable plaster defect, you may need to remove loose material, prepare the edges, apply a compatible filler and redecorate. If a plasterboard joint keeps cracking, you may need joint tape and compound rather than another surface layer of filler.

Cracks where different materials meet may need a detail designed to allow movement. Have a qualified professional specify structural concrete repairs, reinforcement treatment and resin injection. Don't assume that a hard filler or injection product will correct the cause.

What should you ask your builder to do?

Report cracks in writing and ask your builder to inspect them and document the findings, rather than simply repainting. Ask which material has cracked, what caused it, whether movement is continuing and why the proposed repair is suitable.

Request photographs, the repair specification and any engineer's findings for your records. Check your contract and applicable warranty for notification procedures and deadlines, since these vary between projects.

If your builder describes a crack as normal settlement but can't explain its pattern or associated damage, get an independent structural engineer's opinion. Agree on who is responsible for further investigation and for making good afterwards before you allow work that would conceal the evidence.

Sources